Mechanical Punch Rubber Air Spring Reference To S-350-4 / S-200-3 / S-100-3 / S-90-3
S-350-4 / S-200-3 / S-100-3 / S-90-3 can fit for many kinds of Mechanical Punch equipment.
S-350-4 / S-200-3 / S-100-3 / S-90-3 Mechanical Punch air spring is divided into triple, four, five Convolutions. Punch air spring air cushion made of natural rubber through a series of processes made of rubber bladder, used in the punch on the air spring manufacturing process than ordinary industrial air springs to be much more complex, so the cost will be Higher, the price is naturally much higher than the other. In the middle with stainless steel rims, S-200-3 / S-100-3 / S-90-3 three with two rims, S-350-4 four rims with three rims.
Detailed Parameter Table of S-350-4 / S-200-3 / S-100-3 / S-90-3:
|
GUOMAT NO. |
Reference No. |
Hight H(mm) |
Commonly Maximum Stroke(mm) |
The Largest Diameter When Compressed(mm) |
|
Design High(mm) |
Maximum High(mm) |
Minimum Height(mm) |
|
F-350-4 |
S-350-4 |
218 |
336 |
118 |
±85 |
410 |
|
F-200-3 |
S-200-3 |
152 |
232 |
82 |
±53 |
260 |
|
F-100-4 |
S-100-4 |
206 |
296 |
121 |
±60 |
160 |
|
F-90-3 |
S-90-3 |
152 |
222 |
87 |
±45 |
160 |
|
GUOMAT NO. |
Reference No. |
Standard Height,Internal Pressure 0.49 M pa When The General Value |
Using Maximum Internal Pressure (M pa) |
Internal Pressure (M pa) |
|
Effective Area (Cm2) |
Volume(L) |
Load (K n) |
Dynamic Spring Parameters (N/Min) |
Vibration Frequency (Hz) |
|
F-350-4 |
S-350-4 |
960 |
21 |
47.1 |
471 |
1.6 |
0.88 |
3.9-4.9 |
|
F-200-3 |
S-200-3 |
315 |
5.2 |
15.4 |
235 |
2 |
0.88 |
2.9-3.9 |
|
F-100-4 |
S-100-4 |
79 |
1.95 |
3.9 |
59 |
1.9 |
0.88 |
2.9-3.9 |
|
F-90-3 |
S-90-3 |
79 |
1.4 |
3.9 |
78 |
2.2 |
0.88 |
2.9-3.9 |
Description about the Mechanical Punch equipment:
S-350-4 / S-200-3 / S-100-3 / S-90-3 can use in the most common mechanical press.Such air springs can effectively reduce the vibration, there is a more humanistic role is to reduce noise, is our staff in a relatively quiet environment, to protect the punch equipment and also protect the workers.
The most common mechanical press driven by motor crankshaft connecting rod, eccentric gear (or wrist joints) to make the slider move, and punching machine drive system characteristics to determine the speed in all parts of the stroke and force application. And the mechanical punch depends on the system, the lower the dead point, the greater the force. When considering the same time, mechanical punch can have more impact and is more commonly used in industrial applications.
Most traditional mechanical press is the use of induction motor, the early mechanical press with v motor drive, adjust the coupled mechanical and electrical flow to adjust the torque, later will use inverter driven induction motor, induction motor used in the press will have a flywheel energy storage component, regardless of whether the processing, the flywheel will continue running, to process a flywheel is needed to drive the slider with a clutch to make operation. Later also useful servo motor as the power source of the servo press , the servo press without flywheel energy storage, processing when the drive to work, and can be determined in accordance with the processing characteristics of the slider velocity curve in different locations, can be a difficult process.
Product detail photos Of S-350-4 / S-200-3 / S-100-3 / S-90-3:
